コンテンツにスキップ

Installation (Basler Lights)#

This topic tells you how to install a Basler Light.

ハードウェア#

マウント#

All Basler Lights have mounting holes that allow you to securely install the lights in your working environment. For information about which screws are required, refer to the Mechanical Specifications section in the product topic of your light.

外部コントローラーとライトの接続#

警告 – 感電の危険

Connecting the Basler Light with the power supply turned on may result in electric shock, a fire, or destruction of the light.

  • Make sure that the power source is turned off before connecting the Basler Light.

SLP Strobe Controller#

Basler recommends using the Basler SLP Strobe Controller to control your Basler Light. For more information about how to connect the SLP Strobe Controller to your light, see the Basler SLP Strobe Controller documentation.

ライトの操作#

情報

To find information about how to connect your Basler Light to your camera model, refer to your camera topic. You can find your camera topic in the Area and Line Scan Cameras section under "Models". The "Physical Interface" section in your camera topic describes the the total number of I/O lines, the format of the lines (opto-coupled or GPIO, and the pin assignment.

コネクターのピン番号#

Connector Pin Numbering Basler Light

情報

The connector for SWIR lights differs from the connector of other Basler Lights. SWIR lights are equipped with an M12 5-pin connector, while all other Basler Lights are equipped with an M8 4-pin connector. Both connectors use the same pin-out for installation.

内部コントローラー(電圧制御モード)#

ライトのコネクターのピン割り当ては、ライトを連続的に操作するか、ストロボモードで操作するかによって異なります。詳細については、次の表を参照してください。

連続動作#
注意 – ピンを正しく接続しないと、ライトが損傷するおそれがあります。

確実に次の表の説明に従ってピンを接続してください。指定以外の接続を行うと、ライトが損傷するおそれがあります。

ピン 機能 Wire Colors for Cable M8, Axial
Order Numbers: 2200000898, 2200000899, 2200000900
1 24 VDC 茶色
2 接続なし White
3 24 VDC
4 アース/LED(-) Black
5(M12のみ) 未使用 -

ライトを継続的に動作させるには:

  1. ピン1とピン3に24VDCを供給します。
  2. ピン4を接地します。
ストロボモード#
注意 – ピンを正しく接続しないと、ライトが損傷するおそれがあります。

確実に次の表の説明に従ってピンを接続してください。指定以外の接続を行うと、ライトが損傷するおそれがあります。

ピン 機能 Wire Colors for Cable M8, Axial
Order Numbers: 2200000898, 2200000899, 2200000900
1 24 VDC 茶色
2 接続なし White
3 トリガーソース(5~24VDC)
4 アース/LED(-) Black
5(M12のみ) 未使用 -

外部コントローラー(現在の制御モード)#

注意 – ピンを正しく接続しないと、ライトが損傷するおそれがあります。
  • ピン1:外部LEDコントローラーをピン1に接続しないでください。

  • ピン2:外部LEDコントローラーでのみピン2を使用してください。

ピン 外部コントローラー Wire Colors for Cable M8, Axial
Order Numbers: 2200000898, 2200000899, 2200000900
1 接続なし 茶色
2 LED(+) White
3 接続なし
4 アース/LED(-) Black
5(M12のみ) 未使用 -

SLP Strobe Controller#

SLP Strobe Controllerを使用してライトを操作する方法の詳細については、「Basler SLP Strobe Controller」ドキュメントを参照してください。